In this post I’m going to give you some idea of how I approached creating an ebook from artwork I had created about 20 years ago!
The above picture is an actual page from the book with my added copyright. The book was painted on 11 x 17 in. sheets for double spread pages and 8.5 x 11 for normal full pages.
This post will not deal with the uploading of images to Kindle book creator. This is fairly easy once you’ve determined the correct size for the pages you upload. Perhaps that will be for another post.
The first step , of course, is to write out your story. Once you have your concept you can start to write while keeping in mind possible images that might correlate. You may need to edit words and dialogue when it comes to placing it on your image due to space restrictions. In other words as you draw each page it is important to keep in mind that you will need space for text.
Since it was 20 years ago that I created this book I do not have original photos of the process. What I have done is set up pics to give you some idea of how to go about it.
You can of course use all computer generated images. These, however , are the actual pages I drew for the book on both 8.5 x 11 and 11 x 17 paper. This was before private access to the internet and it is exciting to know that the book can be preserved in a way and it’s message made available
Acrylic wash on cold pressed 140 lb paper was used for the final painting. Tubes of acrlic paint were used and the paint was applied in washes much like that of watercolour. The benefit of acrylic paint is that it can be added in layers without disturbing the original coat of paint ( unlike watercolour ).
Begin by cutting your watercolor paper to the required size. Some folks like to pre dampen and stretch the paper to keep it from buckling as it drys. To do this ( I have no pics) you tack or tape your paper to a wooden piece of plywood or better yet a board ( which will have no stains or glues ). You can pour or use a large wash brush to apply generous amounts of water to your paper and let dry. Turn it over if you wish and do the same for the other side. Let the paper dry.
Take the original drawings like as above and flip them over. These are the drawings you drew with 2h and HB pencils. Flip them over like this:
Holding them up to the light by taping them to a well back lit window OR using a light box begin shading in all areas on the reverse side with a 2B ( soft) pencil. You only have to shade areas where there is drawing or lines. You are making a negative transfer as you would use carbon paper ( this dates me I know, ha).
Now place the drawing directly over your watercolor paper. Use some blue low-tack tape to make 2 hinges at the top so you can flip the the drawing page up and down if you need to to see if the transfer is working. But don’t do this often as it could mess up and misalign the drawing. It works like this. Take a dull ( not blunt) F pencil to trace over all your lines. Press down firmly as you trace but not so hard you tear through your paper , of course. When you are done you will have a light transfer of your drawing onto the watercolour paper. You can now begin painting in your colors using your brushes loaded with thin washes.
You may find that a bottle of frisket mask may come in handy if you want to keep highlight areas white; as in snow flakes , for example. The frisket is a liquid rubber that can be painted on or applied to areas you don’t want your paint to color. Wait for it to dry first. Next paint over it. Later with a clean thumb or erasure you can rub it off exposing the paper substrate. You’ll find a convenient tool but not to be overused.
Sometimes, as in the painting above, you may find as I did, that you were not pleased with your first result. If so then prepare another sheet of paper and begin again. You may want to shade over your original transfer drawing a little since some of the 2B pencil may be less impressionable after the first use. Savvy?
In the drawings above the first attempt (top painting) seemed to come out with harsher gradations. I was more pleased with the bottom result.
The last step is to acquire a good quality flatbed scanner and and with your photo software scan the paintings into your computer. For the large paintings you can scan as two parts and use your software ( such as Photoshop or PhotoPaint ) to stitch them together. If this part is beyond your level of expertise then find someone who can do it for you.
As I said , technology can be rather exciting! A 20 year old Children’s Book has been given new life in the cyber-world.
If you’re interested the book is about self worth and it is available from Amazon. The Kindle format is free to download and makes your work look quite beautiful.
Again, thanks for stopping by and visit often or drop me a line. Have a great day!